📋 Ford Mustang Oil Specs at a Glance
Capacity
6.0 qt (2.3L EcoBoost) / 10.0 qt (5.0L Coyote GT, 2018-2023) / 10.0 qt (5.0L S650, 2024+) / 10.0 qt (5.2L Voodoo GT350)
Viscosity
5W-30 full synthetic (2.3L EcoBoost) / 5W-20 (5.0L 2015-2017) / 5W-30 (5.0L 2018+ Coyote Gen3/Gen4) / 5W-50 (GT350/GT500)
Filter
Motorcraft FL-500S (2.3L) / FL-500S (5.0L 2018+) / FL-820S (5.0L 2015-2017) / Fram PH10575 / Mobil 1 M1-212A
Drain torque
21 lb-ft (M14x1.5)
Filter torque
hand-tight 3/4 turn past gasket contact
Interval
7,500 mi normal / 5,000 mi if tracked or driven hard
This guide covers the coupe and convertible (S550 2015-2023, S650 2024-2026, Dark Horse, GT, EcoBoost). A 5.0L Coyote takes 10 quarts - this surprises a lot of first-time DIYers. The GT350 5.2L Voodoo requires 5W-50 and 10 quarts of Motorcraft XL-15W50-5Q (special blend). If you track your Mustang, change at every track day regardless of mileage. The 2024+ S650 GT uses Gen4 Coyote with the same 10 qt / 5W-30 spec.
🛠 What You'll Need
- 6.0 of 5W-30 full synthetic engine oil (Mobil 1 Full Synthetic on Amazon)
- Motorcraft FL-500S (2.3L) oil filter (FRAM equivalent on Amazon)
- Drain pan (drain pan on Amazon)
- Socket for drain plug (metric socket set on Amazon)
- Oil filter wrench or cartridge cap (oil filter wrench on Amazon)
- Torque wrench (1/2" torque wrench on Amazon)
- Funnel (oil funnel on Amazon)
- Floor jack and jack stands or ramps (floor jack on Amazon)
- Latex gloves and shop rags
⚠ Reset the Maintenance LightYour Ford Mustang tracks oil life electronically. After the oil change, you MUST reset the maintenance reminder or the system will think your oil is still aged. Reset procedure varies by model year - see the FAQ below.
✅ Before You Start - Checklist
- Park on level, solid ground
- Confirm exact capacity and viscosity for YOUR engine variant
- Have a new crush washer / filter gasket ready (always replace, never reuse)
- Torque wrench calibrated and set to correct value
- 6.0 of fresh oil purchased - rounded UP, not down
📝 Step-by-Step: Ford Mustang Oil Change
- Confirm your engine variantOpen the hood and check the engine cover or VIN sticker. Capacities differ between trims (6.0 qt (2.3L EcoBoost) / 10.0 qt (5.0L Coyote GT, 2018-2023) / 10.0 qt (5.0L S650, 2024+) / 10.0 qt (5.2L Voodoo GT350)). Buy the right amount of oil and the matching filter.
- Warm the engine 5-10 minutesWarm oil drains faster and more completely. Do not run to full operating temperature - the drain plug will burn you.
- Lift and secure the Ford MustangUse ramps or jack the front and place jack stands on the frame rails. Never work under a vehicle held only by a jack.
- Remove the underbody panel if equippedMost Ford models have a plastic skid panel held by 4-8 fasteners. Remove it for clear access to the drain plug and filter.
- Position drain pan and remove the drain plugOffset the pan 6-8 inches forward of the drain plug - oil shoots sideways at first. Use the correct socket (typically 14mm-19mm). Keep inward finger pressure as the plug spins free so it does not drop into the pan.
- Drain fully (10 minutes minimum)Wait until only single drops fall. Wipe drain plug threads clean. Discard the old crush washer.
- Install new crush washer and reinstall drain plugHand-thread first to avoid cross-threading. Then torque to 21 lb-ft (M14x1.5). Over-torquing strips the oil pan (a $400-800 mistake).
- Move pan under the oil filterOil pours out as you loosen the filter or cap. Reposition the drain pan.
- Remove the old filterFor spin-on filters, use the filter wrench counter-clockwise. For cartridge housings (common on Ford Mustang), use the correct cap socket and remove the housing top. Pull the old element straight up.
- Install the new filter or elementSpin-on: pre-lube the rubber gasket with fresh oil, thread on by hand, then hand-tight 3/4 turn past gasket contact. Cartridge: install new O-rings (always included with cartridge), drop in new element, torque housing cap to hand-tight 3/4 turn past gasket contact.
- Lower the Ford Mustang and refill with new oilRemove the oil filler cap on the valve cover. Pour in slightly less than spec (6.0 target - pour 6.0 first, then check dipstick).
- Start engine and verify no leaksIdle 30-60 seconds. The oil pressure light should extinguish within 5 seconds. Shut off and inspect the drain plug and filter from below - no drips allowed.
- Check dipstick and top off to MAXWait 2 minutes for oil to settle into the pan. Pull dipstick, wipe, reinsert fully, pull. Add oil to the MAX mark - do NOT overfill (overfilling foams the oil and damages bearings).
- Reset the maintenance reminder and record the changeReset via dashboard menu (procedure in FAQ below). Write the date and mileage on a sticker or in the door jamb. Next change at 7,500 mi normal.
🔗 Related Guides
❓ Ford Mustang Oil Change FAQs
What oil does a Ford Mustang take?
Ford Mustang: 5W-30 full synthetic (2.3L EcoBoost) / 5W-20 (5.0L 2015-2017) / 5W-30 (5.0L 2018+ Coyote Gen3/Gen4) / 5W-50 (GT350/GT500). Capacity is 6.0 qt (2.3L EcoBoost) / 10.0 qt (5.0L Coyote GT, 2018-2023) / 10.0 qt (5.0L S650, 2024+) / 10.0 qt (5.2L Voodoo GT350). Always use API SP / ILSAC GF-6A rated oil from a name brand (Mobil 1, Castrol Edge, Pennzoil Platinum, Valvoline Advanced).
What oil filter does a Ford Mustang use?
OEM and quality aftermarket options for the Ford Mustang: Motorcraft FL-500S (2.3L) / FL-500S (5.0L 2018+) / FL-820S (5.0L 2015-2017) / Fram PH10575 / Mobil 1 M1-212A.
How much oil does a Ford Mustang hold?
6.0 qt (2.3L EcoBoost) / 10.0 qt (5.0L Coyote GT, 2018-2023) / 10.0 qt (5.0L S650, 2024+) / 10.0 qt (5.2L Voodoo GT350). Always verify against your specific engine variant - capacities differ between trims.
How often should I change the oil in my Ford Mustang?
7,500 mi normal / 5,000 mi if tracked or driven hard. Severe service means towing, dusty conditions, lots of short trips, or extreme temperatures. Most Ford Mustang owners benefit from changing earlier than the maximum spec.
What is the drain plug torque for a Ford Mustang?
21 lb-ft (M14x1.5). Use a torque wrench - over-tightening strips the oil pan and a replacement pan costs $400-800 in parts plus labor.
How do I reset the maintenance light on a Ford Mustang?
Procedure varies by year and model. Most Ford vehicles use the steering wheel menu or dashboard buttons to navigate to the oil life reset. Consult your owner's manual or search "Ford Mustang oil reset [year]" for the exact button sequence.